Search
You can find the results of your search below.
Fulltext results:
- Stripping the donor
- sure releasing under control at the valve, not by cutting pipes! Always have a first aid kit at hand a... irst and check all lights/features every time you cut a single wire. More information can be found in t... brake pipes noting where they are connected from. Cut or unscrew the rear brake pipe at the junction on... not have a hoist available then it's possible to cut the body in to smaller sections using a reciproca
- Stripping the donor
- sure releasing under control at the valve, not by cutting pipes! Always have a first aid kit at hand a... .php/serviceman:08-09:front_suspension.pdf]] were cut to remove. All the other bolts I removed I cleane... front_suspension.pdf]] I used an angle grinder to cut off the ends that protruded then applied a lot of... ly there is a steel sleeve to remove. Once or two cuts in this with a hacksaw taking care not to cut in
- Floors & Sides
- = Currently supplied kits already have the floor cut or welded in if chosen, you can skip the first two steps if you don't need to cut your floor from sheet aluminium. Cut the alloy floor as shown in the picture, you lay the chassis on ... he alloy, mark around it with a felt pen and then cut with a jig saw with a fine blade. {{ wiki:Image-
- Suspension
- ting the front shock absorbers it is necessary to cut out the centre bridge of the top wishbones to gai... return the level of stiffness they had before you cut out the bridge. 2 bolts are required 8mm each sid... . {| style="margin: auto;" |- | {{wiki:Suspensioncutaway.jpg?300}} | {{wiki:Suspensioncutaway2.jpg?200}} | {{banana.jpg?300}} |} You may need to trim the
- Engine
- e a shapes that fouls against the tunnel. You can cut and weld the existing midpipe to fit which would ... f you do not have access to a welder then you can cut any additional length from the mid pipe and join ... right sides. The most common way to do this is to cut an exhaust hanger off your old MX5 back box, and
- Fuel Tank
- it is leak free. The original neck needs to be cut to make the middle metal pipe as shown, this is a... ts to help stop the GRP stressing. It needs to be cut off and then filled in the centre to allow the pl... cure. The original breather hose can be used and cut down slightly to give a bend without kinking. {
- Lighting & Instruments
- ty of redundant plugs, just don’t be too hasty in cutting them off as you may find you have created an ... h with other apparatus that you may be tempted to cut, but replacing the ground wire with a new one to ... olted to the column mount plate. You will have offcuts from the floor. You could make an alloy surround
- Body Work and Mirrors
- d, it will probably look something like this with cut outs enabling the wiring to be feed in {{:guide:00001274-photo-2023-03-08-10-12-00_tray_with_cutouts.jpg?400|}} ===Side panels=== Major cutting is required to get the side panels to fit, here are e
- Supercharging the Exocet
- s on there tight... really, really tight! You can cut them off (not recommended) or use a special pulle... by lowering the upper front chassis support bar (cut off & re-welded lower). This allows me just enoug... es over the top of the radiator without having to cut the bonnet. Airflow is important, particularly w
- Bodywork & Mirrors
- 6eabd-c563-49fc-a769-a9c0925b6a73.jpeg?400|}} 4. Cut out the hole - you’ll have to overcome FOFU (fear of f***ing up)! I used a hole cutter & abrafile and finished with a half-round file
- MK3 (NC) Pedals & Steering
- the column did not align with the frame holes. I cut about 8mm off the bottom of the steering column w... n order to fit the brake pedal a small corner was cut out off the bracket as the lug for mounting the s
- Pedals & Steering
- e driver side of the bulkhead. Normally these are cut off and placed on the engine bay side, depending ... Steering Rack De-powering ==== It is possible to cut the feed and return pipes on the power steering r
- Seats & Harnesses
- own flat by: - Bending the front mount flat - Cutting off the seatbelt mounting plate - Cutting a small triangle out of the rear mount, bending flat &
- Wiring
- completely from the connectors rather than simply cutting them. You need to take care as often the wire... you trace the wires full length before making any cuts or removing. Some will be obvious (like heated s
- Brake / Clutch / Fuel Lines
- fuel pipe connections from the donor, you simply cut way the original hose and it leaves a barbed fitt
