Search
You can find the results of your search below.
Fulltext results:
- Lighting & Instruments
- ws on the lens, ensure they point the right way. Front indicators need to be seen from 20 degrees (if be... A 10mm hole will need drilling in the side of the front lamp to mount the front indicator on the side as shown below. For IVA the headlight will need rotating i... oy beam near diff. * One to alloy beam near the front. * One strap from the engine to chassis above t
- Suspension
- ====== Suspension ====== When fitting the front shock absorbers it is necessary to cut out the centre br... g?300}} |} You may need to trim the edge of your front subframe for clearance of the wishbones. You may ... wiki:Image--044.jpg?300 }} **When assembling the front top suspension arm, please make sure to install the bolt from the rear to the front, so the nut is on the front face. Failure to foll
- Turning off airbag light
- oaches have been taken for the fogs lights as the front are not compulsory. Some people have fitted the front fogs for IVA as the stalk has a switch for front and rear fogs. Other whose donor had front fog lights have bought (from eBay) a stalk from a model which
- Supercharging the Exocet
- - £200**__ I chose the M45 because… it fits! The front suspension towers of the Exocet are a fair bit fu... went for #3 and mounted the Intercooler (£100) in front of the radiator connected up between the throttle... ced induction in its future by lowering the upper front chassis support bar (cut off & re-welded lower). ... , particularly when introducing an intercooler in front of the radiator. Air will follow the path of leas
- MK3 Build Section
- ount spacer incorrect (potentially rectified) - Front Wing Stay need wheel spacer - Rear Wing Stage n... ll - Top of tunnel panel poor fitting, loose at front, tight at back - Petrol tank does not fit race
- Seats & Harnesses
- be modified to bolt down flat by: - Bending the front mount flat - Cutting off the seatbelt mounting
- NC Mating the Chassis
- 2 longer bolts to replace existing bolts holding front brake calipher to sub frame M12 x 1.25mm thread l
- Body Work and Mirrors
- se, the one on top of the tunnel (too wide at the front and too tight at the rear end), the covering of t
- Stripping the donor
- The aim is to remove the body shell and leave the front sub-frame with the engine, and the rear sub- fram... too much. {{:guide:rearpinchbolt.jpg?400|}} == Front Lower Control Arm == The bolts in '4' in the low... ps://exocet.uk/lib/exe/fetch.php/serviceman:08-09:front_suspension.pdf]] were cut to remove. All the othe... then push out easily {{youtube>3nBsnw8D7HI?}} == Front Upper Control Arms == The bushes in 3 [[https://
- Fitting the fuel tank
- l take is bolted onto these brackets, putting the front of the taken under the frame seems a good option ... r rollover valve {{:guide:tankholes.jpeg?400|}} Front of fuel tank under brackets of frame makes it easier to fit boot cover, but some had to trim the front of the tank and sides too {{::fronttankunderfram... acket holding the boot cover, in this example the front of the boot cover is wedged against the middle ba
- Wing Stays
- ar ones are not high enough to clear the tyre The front and rear ones rub against the wheel (MEV suggest ... ay_bidge_1.jpg?400|}} ===Fixing the stays=== The front stay should be packed with some washers (there ar
- IVA Guide
- rees out at the rear right down to the floor. * Front lights need to be seen at 20 degrees to the oppos
- Brake / Clutch / Fuel Lines
- n arrow pointing away from the valve body and the front brake line to the "F" port. It is necessary to split this output to both front wheels as shown in Fig5 below. {| style="margin:... inside the tank. One single fuel pipe runs to the front via a fuel damper located near the engine. {{ wi
- Mating the chassis
- The rear anti roll bar is left in place but the front one needs bolting to the chassis with 4 8mm bolts
- Stripping the donor
- The aim is to remove the body shell and leave the front sub-frame with the engine, and the rear sub- fram... ful as this may be pressurised. * Unscrew the 2 front brake pipes noting where they are connected from.... ear callipers. * Remove the 4 bolts holding the front antiroll bar to the body, there is provision for ... s on the Exocet. * Support the underside of the front and rear sub-frames with substantial props or use
