Search

You can find the results of your search below.

Fulltext results:

Brake / Clutch / Fuel Lines
5 Hits, Last modified:
d can simply remove the ABS warning bulb from the original dash clocks if needed. Here are some images show... alve. If converting from ABS to non-ABS using the original ABS master cylinder (2 output ports) using the no... | {{:brakesetupfig5.png?400}} |} This shows the original non-ABS setup and configuration. {{ :2270b310-3e3... hose linked below. A few builders have used the original OEM fuel pipe connections from the donor, you sim
Fuel Tank
5 Hits, Last modified:
ble to use a number of cheap parts along with the original fuel neck breather and flange. The tank uses a sm... nd or simply use a 51mm hose and then part of the original rubber hole attached to the metal inlet on the ta... is method please make sure it is leak free. The original neck needs to be cut to make the middle metal pip... "tap" in to the hose. The metal flange end of the original pipe can also be used as a backing for the neck f
Wiring
4 Hits, Last modified:
For a solution soldering the extension wires to original wires, but original didn't want to accept solder, so I used red butt crimps and staggered the connections. ... === The fuse box is not in the same place as the original and some wires will need extending {{:guide:0000... 2023-05-07-13-27-00_skid_control_unit.jpg?400|}} Original install of traction control unit {{:guide:000041
MEV Exocet Build Guide
3 Hits, Last modified:
Exocet build guide. This is a combination of the original UK build guide and contributions from builders. A... build and safety other than you. This is not the original build guide by MEV, however, it was used as a bas... viceman|**Service Manuals & Wiring Diagrams**]] | Original Mazda MX-5 service manuals and wiring diagrams. |
Suspension
2 Hits, Last modified:
replacements can be bought on eBay (cheaper) but original ones are generally a better fit. The joint should... et them up for track or fast road rather than the original MX5 setup. This can also be done manually with s
Suspension
2 Hits, Last modified:
builders take this opportunity to change out the original Mazda bushes, as most are 20+ years old. Dependin... yurethane, this gives a much firmer ride than the original rubber and is actually cost effective compared to
Engine
1 Hits, Last modified:
ne very close to stock as the Exocet uses all the original wiring and sensors. However many builders will us
images
1 Hits, Last modified:
al images and text used from the MEV build guide, original copy [[https://mevltd.co.uk/kit-cars/mev-exocet|h
Radiator
1 Hits, Last modified:
ide:bonnet_me.jpg?400|}} {{::00003708-photo-2023-06-24-17-00-35_radiator_original_bottom_bracket.jpg?400|}}
Radiator
1 Hits, Last modified:
int in the cooling system. Many choose to bin the original large plastic tank for a much more compact alloy
Seats & Harnesses
1 Hits, Last modified:
ats can be made to fit using the runners from the original seat base. This provides adjustment forward and b
special_thanks
1 Hits, Last modified:
to Stewart Mutch from MEV for letting us use the original build guide as a base for the wiki. A big thanky
Supercharging the Exocet
1 Hits, Last modified:
attached to the mini, so it’s probably still the original stuff in it. It doesn’t take very much and you ca
Suppliers
1 Hits, Last modified:
tps://www.mx5parts.co.uk/|MX5 Parts - Import some original parts from direct from Mazda In Japan for less th
Wheels
1 Hits, Last modified:
rent kit comes supplied with wider wings then the original kit, it's possible to now fit up to a 235mm tyre