https://exocet.uk/ 2026-05-15T14:58:05+00:00 https://exocet.uk/ https://exocet.uk/lib/exe/fetch.php/wiki:dokuwiki.svg text/html 2023-11-22T17:26:52+00:00 Anonymous (anonymous@undisclosed.example.com) https://exocet.uk/doku.php/ncmating_the_chassis?rev=1700674012&do=diff NC Mating the Chassis Getting the kit home A long wheel base van is recommended Although it can be done with a trailer Mounting the frame It can be lifted on by a couple of people but easier if you have an engine crane, try and get the frame balanced evenly from the crane text/html 2023-11-22T16:19:07+00:00 Anonymous (anonymous@undisclosed.example.com) https://exocet.uk/doku.php/ncstripping_the_donor?rev=1700669947&do=diff Stripping the donor We assume that you will take all precautions and use proper personal protective equipment, ensuring you and anyone present is not in any danger. Obvious dangers include parts snapping, flying objects, heavy weights, sharp edges, fuel and electrics, The suspension springs on MX5’s are highly preloaded, removing them with the body in place holding them down is the way to go in the absence of spring compress tools. text/html 2021-02-04T11:51:57+00:00 Anonymous (anonymous@undisclosed.example.com) https://exocet.uk/doku.php/rust_removal_prep?rev=1612439517&do=diff Rust Removal and Preparation To keep your build cost friendly you will be reusing a lot of parts from your donor car, of which most will have seen thousands of miles in all weather and are probably not looking their best. For items such as wishbones you can of course buy new however this method gets expensive quickly, so here we will cover on the typical ways for getting those rusty parts back to a text/html 2021-03-09T13:51:10+00:00 Anonymous (anonymous@undisclosed.example.com) https://exocet.uk/doku.php/stripping_the_donor?rev=1615297870&do=diff Stripping the donor We assume that you will take all precautions and use proper personal protective equipment, ensuring you and anyone present is not in any danger. Obvious dangers include parts snapping, flying objects, heavy weights, sharp edges, fuel and electrics, The suspension springs on MX5’s are highly preloaded, removing them with the body in place holding them down is the way to go in the absence of spring compress tools. text/html 2021-12-03T16:30:33+00:00 Anonymous (anonymous@undisclosed.example.com) https://exocet.uk/doku.php/mating_the_chassis?rev=1638549033&do=diff Mating the chassis Before you proceed you might want to refresh the “skate” including the engine, clutch, bushes etc. You can read more about them from the main sections Now you can lower the chassis on to the rolling PPF (power plant frame) and bolt it up. Use washers between the sub frame and chassis on the rear 4 bolts. text/html 2026-01-04T20:06:36+00:00 Anonymous (anonymous@undisclosed.example.com) https://exocet.uk/doku.php/ncmenu?rev=1767557196&do=diff MK3 Build Section More sections are to be added soon from the build guide. For now, this can be accessed from the website links. There is Mk3 builders WhatsApp group, to gain access tag Keith Traynor in the Facebook Group MEV Exocet Owners Group UK and then he will arrange for access. This group isn't open just to stop advertisers etc. It's very friendly and super helpful text/html 2024-05-28T13:27:11+00:00 Anonymous (anonymous@undisclosed.example.com) https://exocet.uk/doku.php/supercharger?rev=1716902831&do=diff Supercharging the Exocet Firstly, you'll need to understand the principals of supercharging, and then (hopefully) it all makes sense which makes it easier to build – if you already know, then skip this bit! Supercharging, like turbo charging is a method of achieving forced induction, which is essentially blowing air into your inlet manifold (this is why superchargers are often called “blowers”) instead of letting the pistons suck air into the inlet manifold – this is referred to as being “na… text/html 2021-03-01T11:38:02+00:00 Anonymous (anonymous@undisclosed.example.com) https://exocet.uk/doku.php/wing_stays?rev=1614598682&do=diff Wing Stays The wing stays are supplied in a set of 4. You will see from the picture below that the rear pairs are attached by drilling an 8mm hole in the rear upright for one bolt and the other is attached to the top calliper bolt with a bolt that is 6mm longer than the donor. You can drill with the suspension assembled. Just remove the shock absorber and use an electric drill from the inside, it is forged so fairly easy to drill. Alternatively remove the top wishbone bolt to allow access by pi… text/html 2024-02-05T14:47:44+00:00 Anonymous (anonymous@undisclosed.example.com) https://exocet.uk/doku.php/bodywork_mirrors?rev=1707144464&do=diff Bodywork & Mirrors Bonnet lock down There are various fittings on the market from bonnet pins to flush catches and Dzuz type fasteners. Fitting fasteners to the top of the bonnet with the locating pins attached to the chassis is a popular option. text/html 2025-01-21T17:40:46+00:00 Anonymous (anonymous@undisclosed.example.com) https://exocet.uk/doku.php/lighting_instruments?rev=1737481246&do=diff Lighting & Instruments Lighting positions are very important. The light emitting surfaces of the headlights have to be a minimum of 500mm from the ground. All lights except fog and reverse need to be within 400mm of the edge of the wings. Rear lights need to be a minimum of 350mm from the ground. The fog light needs to be on the offside or centre line, and the reverse light on the nearside, or centre line and they have to be a minimum of 250mm from the ground. The fog light must be e marked and… text/html 2023-11-07T16:53:52+00:00 Anonymous (anonymous@undisclosed.example.com) https://exocet.uk/doku.php/ncpedals_steering?rev=1699376032&do=diff MK3 (NC) Pedals & Steering NC Adjusting Steering Column Length to Align with frame holes When attempting to fit the steering column the hole in the middle and top of the column did not align with the frame holes. I cut about 8mm off the bottom of the steering column where the splines go into the swivel joint and then everything just about lined up when bolted together. Heat applied to the swivel joint before knocking it off the steering column. text/html 2021-06-10T07:47:44+00:00 Anonymous (anonymous@undisclosed.example.com) https://exocet.uk/doku.php/floors_sides?rev=1623311264&do=diff Floors & Sides Currently supplied kits already have the floor cut or welded in if chosen, you can skip the first two steps if you don't need to cut your floor from sheet aluminium. Cut the alloy floor as shown in the picture, you lay the chassis on the alloy, mark around it with a felt pen and then cut with a jig saw with a fine blade. text/html 2024-02-05T14:42:49+00:00 Anonymous (anonymous@undisclosed.example.com) https://exocet.uk/doku.php/fuel_tank?rev=1707144169&do=diff Fuel Tank If you are looking for more information about running the fuel lines see Brake / Clutch / Fuel Lines The MX5 fuel tank fits under the rear cover. Brackets are welded to the chassis and holes need to be drilled in these to mount the tank. The filler pipe and filler cap from the MX5 can be used. (Be aware of IVA regulations that if the fuel cap is not lockable it must be tethered, if it is lockable it must not be possible to remove the key from the filler cap until it is locked back in… text/html 2023-11-11T11:18:31+00:00 Anonymous (anonymous@undisclosed.example.com) https://exocet.uk/doku.php/iva_guide?rev=1699701511&do=diff IVA Guide Here is an Helpful hints on how to pass the IVA You are required to ensure that there are no edges (contactable with a 100mm diameter sphere - you can make your own easily with some pvc pipe, pu adhesive and a metal semi-sphere from a craft shop / ebay) that are less than 2.5mm in radius. This includes edges of wishbones and any accessible nuts and bolts. Below is an example of nut covers and edge trim. You can use rubber tube such as heater hose or petrol pipe to cover nuts. There i… text/html 2023-11-22T08:33:48+00:00 Anonymous (anonymous@undisclosed.example.com) https://exocet.uk/doku.php/recommended_tools?rev=1700642028&do=diff Recommended Tools Most common hand tools will be used at some point during the strip down of your donor car and while building the Exocet kit car. Required: * Metric sockets, 6 point recommended. Commonly 10,12,13,14,17mm. * Metric spanners * text/html 2024-08-23T20:27:20+00:00 Anonymous (anonymous@undisclosed.example.com) https://exocet.uk/doku.php/suspension?rev=1724444840&do=diff Suspension When fitting the front shock absorbers it is necessary to cut out the centre bridge of the top wishbones to gain clearance. This depends on the diameter of your chosen shock body. Banana shaped 6mm thick plates are provided to bolt to the wishbones in order to return the level of stiffness they had before you cut out the bridge. 2 bolts are required 8mm each side, flip them over if they do not clear your shocks.