Fulltext results:
- Supercharging the Exocet
- |}} I went for #3 and mounted the Intercooler (£100) in front of the radiator connected up between t... ck the numberplate is removed. {{ :picture13.jpg?1000 |}} __**Bypass Valve (BPV) – £20**__ Wh... s disabled. {{:picture15.jpg?300|}} {{:IMG_1021.jpeg?350|}} __**2nd Throttle body (TB) & cabl... bolt holes to give a little wiggle room. {{ :IMG_1016.jpeg?250 |}} I used a digital inclinometer (~
- Lighting & Instruments
- and have a B or an F marking and be a minimum of 100mm from the stop/tail light. Ensure the fog light... to the chassis fixes things! ===Headlights=== A 10mm hole will need drilling in the side of the fron... 0mm from the ground. Fog needs to be a minimum of 100mm from the stop/tail light. The fog light must b... e 2 relays - has a resister sign under it) with a 10 Ohm resistor. Lights will then flash at the corre
- IVA Guide
- nsure that there are no edges (contactable with a 100mm diameter sphere - you can make your own easily... & inlet manifold. {{ :da10ed9e-ee61-4111-80f2-4d410b5c996c.jpeg?400 |}} ===DRIVING TO THE IVA TEST==... 00 rpm. Or 132 BHP if 1.8 engine. * 4v enter; 110 mph. * 4w axle 1 500 axle 2 500 gross 1000 train NA * 4x tick; NO. Go to part 9. And don't forge
- Body Work and Mirrors
- o be feed in {{:guide:00001274-photo-2023-03-08-10-12-00_tray_with_cutouts.jpg?400|}} ===Side panel... ittings.jpg?400|}} {{::00004194-photo-2023-07-21-10-50-04_bonnet_catches_inside.jpg?400|}} A slightl
- MK3 Build Section
- s build [[https://www.facebook.com/profile.php?id=100083086012945|MEV Exocet Mk3 build diary]] Not in... ount the various things (frame does have the main 10 bolts to mount it to subframes) Gotcha or things
- Wing Stays
- dea to use the ones without the lip {{:guide:00001042-photo-2023-02-05-18-48-24_hub_centric_spacers.j... get a flush finish. {{:guide:00000274-photo-2022-10-10-17-19-50_wing_stay_grind.jpg?400|}} ===Fixing the Mudguards=== This was I believe from the first
- Rust Removal and Preparation
- rill, this will take a long time and won't remove 100% of the rust in all cases so something more aggr... oating. This if done correctly can remove near to 100% of rust from a part and because the powder coat
- Wheels
- known as ET, basically you are looking for around 10-0mm offset. So for example if you have a set of 1... mm spacers to achieve 0 or 20mm spacers to get to 10mm offset. Without the correct spacers the car wil
- Formatting Syntax @wiki
- fresh period defaults to 4 hours. Any value below 10 minutes will be treated as 10 minutes. [[wiki:DokuWiki]] will generally try to supply a cached versio
- Build Overview
- Build Overview ====== The launch of Exocet in 2010 created a storm in the kit car industry. Heralded... and make it even better and cost even less! Over 1000 Exocet kits now sold, this is the most popular
- Floors & Sides
- o the chassis. You will need to mark the holes at 100mm centres. Take extra care when marking the hole
- Brake Clutch Fuel Lines
- uellines.jpg?400|}} {{:guide:00000334-photo-2022-10-30-12-56-02_fuel_lines_along_gearbox.jpg?400|}}
- Fitting the fuel tank
- nd a rollover valve {{:guide:00000337-photo-2022-10-30-12-59-42_fuel_tank_rollover_valve.jpg?400|}}
- NC Mating the Chassis
- long wheel base van is recommended {{:guide:00001017-photo-2023-02-05-17-43-41_frame_in_van.jpg?400|... trying to tighten {{::00004045-photo-2023-07-15-10-20-24_bolt_torque.jpg?400|}} === What additional
- Stripping the donor
- cleaned skate {{:guide:00000073-photo-2022-09-13-10-51-21_skate.jpg?400|}} {| style="margin: auto;"