Search

You can find the results of your search below.

Matching pagenames:

Fulltext results:

Brake / Clutch / Fuel Lines
17 Hits, Last modified:
====== Brake / Clutch / Fuel Lines ====== ===ABS and Proportioning valve=== Most late donors come with ... along with the pump. You can then also modify the brake lines to suit. You will also need to replace your... alve with that from a non-abs car and connect the brakes as per the diagram below. You will not need to m... e side for the 2nd connection from the end of the brake cylinder. Then connect your rear brake line to th
IVA Guide
5 Hits, Last modified:
garage & back for you on trade-plates. * Check brake flex hoses do not contact anything on full lock b... e there is a specified fluid label on or near the brake reservoir area. * Obvious one, check the horn a... eed a IVA compliant yellow sticker on or near the brake booster indicating the grade of fluid to be used.... a non-return valve to the vacuum hose between the brake booster & inlet manifold. {{ :da10ed9e-ee61-4111-
MK3 (NC) Pedals & Steering
4 Hits, Last modified:
g}} | {{img_2739.jpg}} | {{img_2741.jpg}} |} === Brake Pedal Fitting === In order to fit the brake pedal a small corner was cut out off the bracket as the lug... kepedal.jpg?300 |}} An alternative is to fit the brake pedal on top you'll see the 2 inner bolts are onl... made some half washers etc. Outer bolts through everything {{:guide:brakeconnection.jpeg?400|}}
Pedals & Steering
4 Hits, Last modified:
above picture. *The spacers on the back of the brake pedal are left attached on the driver side of the... ch to plug back into the loom. *Note there is a brake pedal switch to plug back into the loom. *Note ... n the reservoir, these should have a plug for the brake level warning. *A hole needs drilling then fili... int to the head. *The 'relay' on the end of the brake pedal assembly is for the fuel pump. *Where pre
Stripping the donor
4 Hits, Last modified:
detail, clean and paint all the suspension parts, brakes and sub-frames. {| style="margin: auto;" |- | {... attached to the gearbox via the pipe. Remove the brake/clutch pedal, master cylinder and servo. Keep the... this may be pressurised. * Unscrew the 2 front brake pipes noting where they are connected from. Cut or unscrew the rear brake pipe at the junction on the rear axle. Disconnect
Build Overview
3 Hits, Last modified:
dard MX5 exhaust manifold, prop shafts, steering, brakes, pedals etc. -Costs kept low and convenient by... es. -Ease of testing for road use items such as brake balance, self-centring, emissions, decibels, prot... tune up options available, super/turbo chargers, brake/suspension upgrades. -The Exocet community is a
Handbrake
3 Hits, Last modified:
======Handbrake====== ===Brake Cooling=== A number of people have not refitted the air cooling for the brakes as shown below {{:handbrake:00000956-photo-2023-02-05-16-02-33_brake_cool_not_needed.jpg?400|}} ===Routing HandBrake
MK1 / MK2 / MK2.5 Build Section
2 Hits, Last modified:
e panels. | | {{:052-break.svg?nolink&48x48}} | [[brake_clutch_fuel_lines|**Brake, Clutch & Fuel Lines**]] | Routing of the main lines on the chassis. | | {{:01
Brake Clutch Fuel Lines
2 Hits, Last modified:
====== Brake Clutch Fuel Lines ====== ===Mounting ABS Unit=== {{:guide:absmountj.jpeg?400|}} {{:guide:mountingabsunit.jpeg?400|}} ===Running Fuel/Brake Lines Along Beam=== Do you run the lines along t
NC Mating the Chassis
2 Hits, Last modified:
ger bolts to replace existing bolts holding front brake calipher to sub frame M12 x 1.25mm thread length ... nger bolts to replace existing bolts holding rear brake calipher to sub frame M10 x 1.25mm thread lenght
MK3 Build Section
2 Hits, Last modified:
to replace certain ones that need to be longer (brake caliper bolt and wheel bearing bolt to mount whee... vg?nolink&48x48}} | [[ncbrake_clutch_fuel_lines|**Brake, Clutch & Fuel Lines**]] | Routing of the main li
Suppliers
2 Hits, Last modified:
*[[https://www.spareshut.com/|Spares Hut - Mk3 Brake calipers and a few other bits, very reasonable]] ... Facebook page]] * https://freakyparts.co.uk/ - brakes, clutches & performance parts * https://shop.m
Floors & Sides
1 Hits, Last modified:
rivnuts if that is your preference) for mounting brake or fuel hoses. Commonly P clips are used to hold
Fuel Tank
1 Hits, Last modified:
re information about running the fuel lines see [[Brake_Clutch_Fuel_Lines]] </WRAP> The MX5 fuel tank f
Handbrake
1 Hits, Last modified:
s it is used to check the bulb is working for the brake fluid level test. The plastic handbrake cover fr
Stripping the donor
1 Hits, Last modified: