Fulltext results:
- Build Overview
- uired, just transplant parts to a new lightweight chassis. -Only basic tools are required plus the loan o... HOWEVER CAUSED WHEN USING THIS GUIDE. ===Current Chassis Options=== The Mk1/2/2.5 and Mk3 chassis are offered in the following options below: *Road chassis: *Fully welded chassis with CDS flat top rol
- Mating the chassis
- ====== Mating the chassis ====== Before you proceed you might want to refresh the "skate" including the en... hem from the main sections Now you can lower the chassis on to the rolling PPF (power plant frame) and bolt it up. Use washers between the sub frame and chassis on the rear 4 bolts. {| style="margin: auto;" |-... four bolts used to hold the rear sub-frame to the chassis. On 1.8 cars you may find brackets from the lower
- MK3 Build Section
- , tight at back - Petrol tank does not fit race chassis - Frame modification required for ITBs - Side... & Sides**]] | Method of installing the floor and chassis side panels. | | {{:052-break.svg?nolink&48x48}} ... Fuel Lines**]] | Routing of the main lines on the chassis. | | {{:014-car.svg?nolink&48x48}} | [[ncmating_the_chassis|**Mating the chassis**]] | Lowering of the chassi
- Floors & Sides
- alloy floor as shown in the picture, you lay the chassis on the alloy, mark around it with a felt pen and ... pg?300 }} Next job is to rivet the floor to the chassis. You will need to mark the holes at 100mm centres... may wish to use a sealant such as PU between the chassis and floor to stop it vibrating. **Note:** //While you have the chassis upside down, it is now recommended to drill any h
- MK1 / MK2 / MK2.5 Build Section
- & Sides**]] | Method of installing the floor and chassis side panels. | | {{:052-break.svg?nolink&48x48}} ... Fuel Lines**]] | Routing of the main lines on the chassis. | | {{:014-car.svg?nolink&48x48}} | [[mating_the_chassis|**Mating the chassis**]] | Lowering of the chassis over the skate. | | {{:045-steering_wheel.svg?nolink&48
- Supercharging the Exocet
- ard than the MX5, narrowing the space between the chassis and the engine, so fitting the bigger M62 while p... require some custom work on the SC mounting, the chassis or both. Note: the ’45 & ’62 respectively refer ... duction in its future by lowering the upper front chassis support bar (cut off & re-welded lower). This all... t from the Garage42 kit wouldn't clear the Exocet chassis (as the suspension towers are a bit more in-board
- IVA Guide
- ith a triangle of plastic sheet cable tied to the chassis. Use an off cut from the PVC side panel perhaps. ... .jpeg?400 |}} ===VIN PLATES=== In addition to a chassis VIN plate you must also have a plate with the man... cobbler will be fine, 2 rivets on the dash board chassis tube is all that is required but ensure the manuf
- Lighting & Instruments
- t replacing the ground wire with a new one to the chassis fixes things! ===Headlights=== A 10mm hole will ... POINTS. Very important. * One from Battery to chassis. * One to alloy beam near diff. * One to allo... near the front. * One strap from the engine to chassis above the exhaust manifold. * One multiple eart
- NC Mating the Chassis
- ===== NC Mating the Chassis ===== ===Getting the kit home=== A long wheel base van is recommended {{:guide... I need === The kit supplies bolts to attach the chassis to the sub frame however this page will contain a... resses) 4 bolts to connect Gaz coilovers to the chassis M12 x 1.25mm thread length 40mm 2 longer bolts t
- Radiator
- ==== The radiator is mounted on the front of the chassis. Aluminium brackets can be made by the builder fo... it these as low as possible when using the G-type chassis, this helps bonnet clearance. It is also possible... so that it can fit correctly between radiator and chassis; alternative aftermarket fans are an option and u
- MEV Exocet Build Guide
- oving rust and getting the skate ready before the chassis is mounted. | | {{:010-mechanic.svg?nolink&48x48}... |**MK1 (NA) / MK2 (NB) / MK2.5 (NBFL)**]] | First chassis design made for the MK1, MK2 and MK2.5. | | {{:01... ?nolink&48x48}} | [[ncmenu|**MK3 (NC)**]] | Newer chassis designed for the MK3 platform. | </div> \\ ===
- Suspension
- over if they do not clear your shocks. On early chassis the stock wishbones may clear the suspension unit... e used. It is probably a sensible policy with any chassis to offer up the intended suspension and then make... bolt will foul the anti-roll bar mounting on the chassis will require the frame removed or the bolt cut.**
- Bodywork & Mirrors
- the bonnet with the locating pins attached to the chassis is a popular option. Low mount aerocatches (pic... Using Rivnuts to secure wing mirrors to the top chassis rail is a good idea. Check position a few times b
- Brake Clutch Fuel Lines
- run the lines along the skate before putting the chassis? The choice is yours, probably easier to do before dropping chassis on but if you do it after you know you can get to
- Stripping the donor
- each corner of the suspension so that the rolling chassis may indeed roll without the engine and diff sinki... nsor should be removed or it will rub against the chassis as below, you can buy a lamda sensor plug on ebay