Fulltext results:
- Supercharging the Exocet
- rger (SC) - £200**__ I chose the M45 because… it fits! The front suspension towers of the Exocet are a... the space between the chassis and the engine, so fitting the bigger M62 while possible (and largely th... ). In short, the M62 is better but for me the M45 fits better. The M45 is sourced from a Mini Cooper –... body – this needs to come off to give you room to fit a custom outlet at an angle. - **Fill the (red)
- Body Work and Mirrors
- }} ===Internal Panels=== Issues have been found fitting some of these, the one on top of the tunnel (... 047-photo-2023-05-23-11-19-19_internal_panels_not_fit.jpg?400|}} {{:guide:00003619-photo-2023-06-17-14... jor cutting is required to get the side panels to fit, here are examples of a good job {{:guide:000048... for IVA {{ ::00004817-video-2023-09-11-17-44-35_fitting_panels.mp4 |}} ===Fitting the bonnet=== Her
- Suspension
- cheaper) but original ones are generally a better fit. The joint should be covered in grease before fitting the cover {{:guide:00000798-photo-2023-01-05-21-22-45_greasing_ball_joints.jpg?400|}} === Fitting Poly Bushes === All of the bushes went is ea... hen found this link [[https://www.powerflex.co.uk/fitting-guides]] which showed it is supposed to twist
- Bodywork & Mirrors
- ====== ===Bonnet lock down=== There are various fittings on the market from bonnet pins to flush catches and Dzuz type fasteners. Fitting fasteners to the top of the bonnet with the l... of the bonnet clear and are a little trickier to fit but it can be done… {{ :adeb88f1-471c-4008-8499-... e and spend the effort to file it out for a tight fit as the holes for the tiny mounting bolts are real
- IVA Guide
- ng back lights to instruments. * If you plan on fitting fly screens, it’s a good idea to fit them after the test to save having to worry about complying w... tly fixed, if visibility is impaired from it then fit a near side mirror too. {{ :e17c1580-0f1f-4a89-bb... ) until the car is registered. If you have plates fitted, tape them up when you drive to & from the tes
- MK3 (NC) Pedals & Steering
- to Align with frame holes === When attempting to fit the steering column the hole in the middle and to... 2739.jpg}} | {{img_2741.jpg}} |} === Brake Pedal Fitting === In order to fit the brake pedal a small corner was cut out off the bracket as the lug for mou... ::ncbrakepedal.jpg?300 |}} An alternative is to fit the brake pedal on top you'll see the 2 inner bol
- MK3 Build Section
- nnel panel too small - Top of tunnel panel poor fitting, loose at front, tight at back - Petrol tank does not fit race chassis - Frame modification required for ... Harnesses**]] | Seats that can be used along with fitting instructions. | | {{:017-car.svg?nolink&48x48
- Wing Stays
- hem to the underside with PU adhesive. If you are fitting the LED lights into your kick wings or G-type wings fit them before fitting wings to car. It is important that thread lock paste is used on the calliper bolt
- Brake / Clutch / Fuel Lines
- ep ABS to pass the IVA test even if the donor was fitted with it. If you wish to remove the ABS system... cut way the original hose and it leaves a barbed fitting to connect to the tank or fuel rail. The fue
- Floors & Sides
- The plastic sides are easy to trim to shape and fit using self tapping screws at 150mm centres. It lo... concealed fixings. The panel may need trimming to fit {| style="margin: auto;" |- | {{wiki:Image--016.
- Fuel Tank
- e_Clutch_Fuel_Lines]] </WRAP> The MX5 fuel tank fits under the rear cover. Brackets are welded to the... filled in the centre to allow the plastic neck to fit secure. The original breather hose can be used a
- Handbrake
- plastic handbrake cover from the donor will need fitting and you may be tempted to make a cover for the cables too. Don’t forget to fit a gaiter around the gear lever too. Much neater w
- Fitting the fuel tank
- ====== Fitting the fuel tank ====== The fuel take is bolted onto these brackets, putting the front of ... l tank under brackets of frame makes it easier to fit boot cover, but some had to trim the front of the
- Wiring
- n be placed in the tray or a full size one can be fitted behind the passenger side (helpful if the pass... s before starting to prune the harness=== If you fit the loom and get everything running you can then
- Pedals & Steering
- m to be quite hard plastic and just don't seem to fit. The right hand ones for a Citroen Berlingo 1996-2011 (part no 406643) fit almost perfectly and are sensibly priced. The sma