Search
You can find the results of your search below.
Fulltext results:
- NC Mating the Chassis
- nded {{:guide:00001017-photo-2023-02-05-17-43-41_frame_in_van.jpg?400|}} Although it can be done with a ... kit_collected_trailer.jpg?400|}} ===Mounting the frame=== It can be lifted on by a couple of people but ... sier if you have an engine crane, try and get the frame balanced evenly from the crane {{:guide:00003261-photo-2023-06-04-07-27-56_lowering_frame_on.jpg?400|}} === Protecting frame during the bu
- Stripping the donor
- to remove the body shell and leave the front sub-frame with the engine, and the rear sub- frame with the differential, connected together via the alloy back bo... ng. * Remove the six bolts holding the rear sub-frame to the body shell. * Remove the eight bolts holding the front sub-frame to the body shell. {{ wiki:Image--008.jpg?300 }}
- Mating the chassis
- er the chassis on to the rolling PPF (power plant frame) and bolt it up. Use washers between the sub frame and chassis on the rear 4 bolts. {| style="margin: a... s not necessary to remove the engine from the sub-frame to construct your kit). Below you can see the four bolts used to hold the rear sub-frame to the chassis. On 1.8 cars you may find brackets
- Stripping the donor
- to remove the body shell and leave the front sub-frame with the engine, and the rear sub- frame with the differential, connected together via the alloy back bo... hedskate.jpg?300}} |} === Remove Engine from Sub Frame === Remove the bolts on the rubber end of the en... 023-02-01-14-45-49_lamda_plug.jpg?400|}} === Sub frame disassembly === == Rear Toe Control Pinch Bolt =
- Brake / Clutch / Fuel Lines
- s (rubber lined) to attach the brake lines to the frame as shown. These need to be positioned to ensure... ke and fuel lines is along the driver's side (UK) frame, this is to keep it away from the exhaust and prop shaft. You can alternatively use the PPF frame but please note this can be subject to movement s
- Fuel Tank
- escribed. All tanks also need a good earth to the frame as this will be tested at the IVA inspection, thi... e space under the tank, this can be bolted to the frame. Make sure that it leans away from the exhaust so
- Fitting the fuel tank
- rackets, putting the front of the taken under the frame seems a good option {{:guide:wheretoboltfueltank... jpeg?400|}} Front of fuel tank under brackets of frame makes it easier to fit boot cover, but some had t
- MK3 Build Section
- standard size bolts to mount the various things (frame does have the main 10 bolts to mount it to subfra... ack - Petrol tank does not fit race chassis - Frame modification required for ITBs - Side body pane
- MK3 (NC) Pedals & Steering
- NC Adjusting Steering Column Length to Align with frame holes === When attempting to fit the steering col... ddle and top of the column did not align with the frame holes. I cut about 8mm off the bottom of the ste
- Rust Removal and Preparation
- to your coated if you wanted parts to match your frame. The down side to powder coat is that especially... ormal part should you want it to colour match the frame / bodywork. === Bolts & Fixings === You will
- Suspension
- roll bar mounting on the chassis will require the frame removed or the bolt cut.** ===Bushes=== Many bu... =Anti Roll bar=== This should bolt direct to the frame using the mounting points, however depending on t
- How to edit or create pages in the wiki
- you have uploaded a file you can use the picture frame icon in the editor to insert the picture. You can
- Handbrake
- } {{:guide:routing2.jpg?400|}} The holes on the frame have been found to be too small, a stepped drill
- Radiator
- tor.jpg?300}} |} The brackets need fixing to the frame and it's recommended to fit these as low as possi
