Search

You can find the results of your search below.

Fulltext results:

Supercharging the Exocet
7 Hits, Last modified:
e process) may require some custom work on the SC mounting, the chassis or both. Note: the ’45 & ’62 respec... ications you will need to do: - **Hack off the mounting bracket / tab** on the outlet side of the body – ... 7.jpeg?400|}} {{:IMG_0866.jpeg?400|}} __**Mounting Kit, pulleys & belt - £280**__ There are a few M45 mounting kits out there for the MX5 engine, and like the c
MK1 / MK2 / MK2.5 Build Section
3 Hits, Last modified:
8}} | [[pedals_steering|**Pedals & Steering**]] | Mounting the pedal box and steering rack. | | {{:067-radia... .svg?nolink&48x48}} | [[radiator|**Radiator**]] | Mounting the radiator. | | {{:003-gas_station.svg?nolink&4... } | [[bodywork_mirrors|**Bodywork & Mirrors**]] | Mounting the GRP panels and mirrors. | | {{:066-car_lights
MK3 Build Section
3 Hits, Last modified:
} | [[ncpedals_steering|**Pedals & Steering**]] | Mounting the pedal box and steering rack. | | {{:067-radia... vg?nolink&48x48}} | [[ncradiator|**Radiator**]] | Mounting the radiator. | | {{:003-gas_station.svg?nolink&4... | [[ncbodywork_mirrors|**Bodywork & Mirrors**]] | Mounting the GRP panels and mirrors. | | {{:066-car_lights
Floors & Sides
2 Hits, Last modified:
nd insert rivnuts if that is your preference) for mounting brake or fuel hoses. Commonly P clips are used to... IVA compliant 30cm is the usual distance between mounting points although just needs to be "secure".// {|
Lighting & Instruments
2 Hits, Last modified:
?300}} |} The rear wings have a “kick” to enable mounting of the rear LED lights. This unit contains the st... o sit flush. The fog and reverse lights will need mounting separately paying attention to the IVA requiremen
Stripping the donor
2 Hits, Last modified:
Remove the bolts on the rubber end of the engine mounting as shown below not the bolts that screw into the ... nger side I removed the bolt on top and below the mounting and on the drivers side just the bottom bolt as t
Suspension
2 Hits, Last modified:
disassembly the bolt will foul the anti-roll bar mounting on the chassis will require the frame removed or ... = This should bolt direct to the frame using the mounting points, however depending on the bar you have fro
Bodywork & Mirrors
1 Hits, Last modified:
it out for a tight fit as the holes for the tiny mounting bolts are really close to the edge! {{ :c59d6e9e
Mating the chassis
1 Hits, Last modified:
ition to the welded chassis tabs in the rear (for mounting the rear subframe brace) there is a welded tab on
Brake Clutch Fuel Lines
1 Hits, Last modified:
====== Brake Clutch Fuel Lines ====== ===Mounting ABS Unit=== {{:guide:absmountj.jpeg?400|}} {{:guide:mou
NC Mating the Chassis
1 Hits, Last modified:
-26-12-01-25_kit_collected_trailer.jpg?400|}} ===Mounting the frame=== It can be lifted on by a couple of p
MK3 (NC) Pedals & Steering
1 Hits, Last modified:
corner was cut out off the bracket as the lug for mounting the steering column stopped it from going far eno
Suspension
1 Hits, Last modified:
ach of the coilovers uses two spacers for the top mounting, make sure you use a big and small spacer on each
Wiring
1 Hits, Last modified:
of the mx5 multi way earth blocks which have the mounting tab on them, to bolt to the mev earth points. The
Pedals & Steering
1 Hits, Last modified:
ss to the top of the driver’s side shock absorber mounting plate, see opposite side welded tube. *When bol
Seats & Harnesses
1 Hits, Last modified:
PlayGround @playground
1 Hits, Last modified: