Search
You can find the results of your search below.
Matching pagenames:
Fulltext results:
- IVA Guide
- ing wheel but even the bottom outside edge of the side panel could be called into question, take a file ... tied to the chassis. Use an off cut from the PVC side panel perhaps. {{ :b8406766-6f26-4780-a19c-85cc... on. If you wire the rear fog to come on with the side lights then you will need a self-cancelling switc... if visibility is impaired from it then fit a near side mirror too. {{ :e17c1580-0f1f-4a89-bb33-13fbb58de
- Body Work and Mirrors
- 3-03-08-10-12-00_tray_with_cutouts.jpg?400|}} ===Side panels=== Major cutting is required to get the side panels to fit, here are examples of a good job {{:guide:00004898-photo-2023-09-18-13-12-32_side_panels.jpg?400|}} {{:guide:00004899-photo-2023-09-18-13-12-32_side_panels_1.jpg?400|}} {{:guide:00004903-photo-2023
- Stripping the donor
- .jpg?300 }} Remove the 2 plastic caps from each side of the dash board and remove the 4 bolts. Remove ... . Pull off radio panel. Remove the 2 bolts either side of the radio then remove the plastic surround. Ne... .jpg?300 }} The picture above shows the rear off side bolt being removed, this is one of 3. If they sta... les as the balance is about right. Use front near side hole next to the transmission tunnel and rear off
- Lighting & Instruments
- be seen from 20 degrees (if below 750mm) inwards. Side repeaters need to be seen at 5 degrees from the side of the car from 3m behind. In theory, the wiring ... adlights=== A 10mm hole will need drilling in the side of the front lamp to mount the front indicator on the side as shown below. For IVA the headlight will need r
- Pedals & Steering
- f the brake pedal are left attached on the driver side of the bulkhead. Normally these are cut off and placed on the engine bay side, depending on the steering column length. This is... ce to be bolted across to the top of the driver’s side shock absorber mounting plate, see opposite side welded tube. *When bolting the steering column in th
- Wiring
- the headlight wires are too long for the driver’s side and will need reducing but the passenger side wires are about right including horn and fan and can be k... dy. If you have a MKI donor then it has separate side/indicator units so a slight loom mod is required ... connect to the MEV headlights with indicators and side lights all in one unit. The battery can be mount
- Brake / Clutch / Fuel Lines
- o the firewall) and then the "F" port on the same side for the 2nd connection from the end of the brake ... or the brake and fuel lines is along the driver's side (UK) frame, this is to keep it away from the exha... onnections, however it is looped back at the tank side and the FPR is inside the tank. One single fuel p
- MK3 Build Section
- d wheel spacer (potentially rectified) - Driver side footwell tunnel panel too small - Top of tunnel... ssis - Frame modification required for ITBs - Side body panels are way too big and need a lot of cut... Sides|Method of installing the floor and chassis side panels|:ncfloors_sides|{{:013-car.svg?nolink&48x4
- Supercharging the Exocet
- ocking lobes or blades that draw the air from one side (inlet) and push it out of the other (outlet) – s... ck off the mounting bracket / tab** on the outlet side of the body – this needs to come off to give you ... sits directly above the exhaust manifold (the hot side of the engine). Heat soak from the exhaust to the
- How to edit or create pages in the wiki
- should be able to use the link on the right-hand side as shown below to edit. {{ guide:edit.png?800 }}... edia manager, this can be found on the right hand side once logged in. Once you have uploaded a file you
- Stripping the donor
- ove the bolts at the rubber end. On the passenger side I removed the bolt on top and below the mounting and on the drivers side just the bottom bolt as the manifold stops you ge
- Bodywork & Mirrors
- -round file. Better to make the hole on the small side and spend the effort to file it out for a tight f
- Floors & Sides
- dhesive along the length top and bottom. G-type side panels tuck under the chassis to allow for concea
- Mating the chassis
- frame brace) there is a welded tab on the drivers side of the chassis in the engine bay. This is to moun
- MK1 / MK2 / MK2.5 Build Section
- Sides|Method of installing the floor and chassis side panels|:floors_sides|{{:013-car.svg?nolink&48x48}
