Fulltext results:
- Rust Removal and Preparation
- ld ones out before restoring the parts. === Wire Wheel & Paint === If you have a lot of time but a smal... remove a lot of material very quickly. Brass wire wheels are ideal for cleaning this type of metal and at... cheap, these usually come with a large brass wire wheel that will make quick work of most parts cleaning.... new condition. It is not recommended to use flap wheels or steel wire wheels on aluminium. **__Steel Pa
- MK3 Build Section
- s that need to be longer (brake caliper bolt and wheel bearing bolt to mount wheel spat brackets) - Many other little brackets to mount various things - Al... (potentially rectified) - Front Wing Stay need wheel spacer - Rear Wing Stage not high enough and need wheel spacer (potentially rectified) - Driver side fo
- MK1 / MK2 / MK2.5 Build Section
- f the chassis over the skate. | | {{:045-steering_wheel.svg?nolink&48x48}} | [[pedals_steering|**Pedals &... back to the start of the guide. | | {{:075-alloy_wheel.svg?nolink&48x48}} | [[wheels|**Wheels**]] | ET explained and what wheels you need for the Exocet. | | {{:icons:045-engine-1.png?noli
- IVA Guide
- nuts. There is an exempt zone around the steering wheel but even the bottom outside edge of the side pane... Replicar/Exocet |- |Type of body: |Sports car |- |Wheel Plan: |2 axle rigid |- |Colour: |State body colou... ble mass: |NA |- |Track width: |1450 depending on wheel/spacer choice |- |Width: |NA |- |NOx: |NA |- |Rev... en from donor V5 |- |Cylinder capacity: |1840 |- |Wheelbase: |2240 |- |CO2: |See IVA cert |- |Mass in ser
- Wheels
- ====== Wheels ====== This can be a confusing area. The off-set of the wheels is also known as ET, basically you are looking f... m offset. So for example if you have a set of 15” wheels that have ET 30 stamped on them you will need 30... wiki:Image--048.jpg?300 }} ===Builder Recommend Wheels=== *XXR 15 527 15x8.25 ET0 - Needs a 215mm wi
- Engine
- ======Engine====== ===Removing the flywheel=== How to remove the flywheel spigot bearing without a special tool {{ :guide:00004945-video-2023-09-20-19-12-57_remove_flywheel.mp4 |}} Other found the above tricky and purchas
- Wing Stays
- . You will need a spirit level to ensure that the wheel rim does not protrude beyond a vertical line from... type wing stays are designed to use up to 235mm tyres, see the [[wheels|Wheels]] section for more info.
- Build Overview
- ue British sports car layout of front engine rear wheel drive and offering excellent value for money. One... self, making the choice of colour, nose style and wheels is just the start. Just pick a budget and achiev
- Suspension
- ct&300}} |} ===Setting up the Gaz suspension and Wheel Alignment=== The wheels will need aligning, this can be done at a local tyre centre if they have a Hunt
- Wing Stays
- the tyre The front and rear ones rub against the wheel (MEV suggest using hub centric spaces 25mm bit ru... ng the wing stays to stop the rubbing against the wheel is likely to crack any powder coating if already
- Brake / Clutch / Fuel Lines
- t is necessary to split this output to both front wheels as shown in Fig5 below. {| style="margin: auto;
- Engine
- hen it's also a really good time to change the flywheel if you are wanting a lightened version. {{ :clut
- Handbrake
- nd in the adjusters in the rear pistons until the wheel locks, then do a 1/4 turn back to allow slight mo
- NC Mating the Chassis
- e Chassis ===== ===Getting the kit home=== A long wheel base van is recommended {{:guide:00001017-photo-
- Stripping the donor
- push out the insert. Then used a chisel and wire wheel to remove the rubber. Finally there is a steel sl